Anti Slip Bathroom Tape
 | Anti Slip Bathroom Tape
|
Product Description
Caution Lines Company is a manufacturer of anti slip bathroom tape for wet bathroom floors, shower rooms, bathtub areas, hotel washrooms and private label bathroom safety products. The tape uses a soft PEVA or PVC textured surface with acrylic pressure-sensitive adhesive, giving barefoot grip without loose mineral grit. Strip width, roll length, die-cut shape, color, adhesive level and packaging can be confirmed by samples, including 24-72 hour wet peel, edge lift and residue observation before production.
Product Photos
Technical Data Sheet
Item | Typical Value |
Product Type | Soft surface bathroom grip tape |
Surface Material | PEVA or PVC textured film |
Adhesive Type | Acrylic pressure-sensitive adhesive |
Total Thickness | 0.55-0.85mm typical reference value |
Adhesive Thickness | 0.08-0.15mm typical reference value |
Standard Roll Width | 25mm, 50mm, 100mm or custom slit width |
Standard Roll Length | 3m, 5m, 10m, 15m, 18m or project roll length |
Die-Cut Format | Strip, round dot, oval, S-shape or special drawing shape |
Color Options | Transparent, white, grey, black or matched color |
Peel Adhesion on Glazed Tile | 7-12 N/25mm after 24h dwell, reference value |
Peel Adhesion on Acrylic Tray | 6-10 N/25mm after 24h dwell, reference value |
PVC Bathroom Floor Check | Adhesive level tested for wet holding and clean removal balance |
Wet Exposure Check | 24-72h water contact observation for edge lift, peel change and residue |
Application Temperature | 10-40 C recommended |
Service Temperature | -10-60 C typical indoor bathroom range |
Slitting Tolerance | +/-0.5mm typical |
Die-Cut Tolerance | +/-0.8mm typical, based on shape and material thickness |
Cleaning-Agent Wipe Check | 20-50 light wipe cycles, reference observation |
Color Matching Tolerance | Visual sample approval before production |
Sample Confirmation | Size, adhesive level, color, shape and packaging checked before production |
Product Overview
This anti slip bathroom tape is made for wet barefoot areas where rough stair-grip tape is often too sharp, too dirty-looking, or too difficult to clean. The PEVA/PVC surface has a mild raised texture that helps improve foot contact, while the flexible backing can follow ceramic tile, acrylic shower trays, coated bathtub bottoms and PVC bathroom floors. For typical production reference, total tape thickness is usually 0.55-0.85mm, with an acrylic adhesive layer around 0.08-0.15mm depending on the required bonding level.
Transparent shower grip tape is a good option when the original tile, acrylic or bathtub surface should remain visible. White, grey and black versions are often used where clearer visual guidance is needed, such as hotel washrooms, gyms, care facilities and shared shower rooms. For drainage-sensitive areas, strip, dot and oval layouts can be adjusted according to floor slope, drain position and foot-contact area. Dots and ovals leave more open space for water movement, while long strips create a steady grip path near shower entries and bathtub stepping zones.
Adhesive selection should be based on the actual bathroom surface, not simply on the strongest glue. As a typical reference, peel adhesion after 24h dwell may reach 7-12 N/25mm on glazed tile and 6-10 N/25mm on acrylic shower trays, but results can change with surface coating, cleaning condition and dwell time. For larger orders, samples should be tested for 24-72 hours after water exposure to check wet peel change, edge curling, adhesive overflow and visible residue.
Benefits
- Soft PEVA/PVC texture is more comfortable for bare feet than mineral grit tape.
- The surface is easier to wipe clean and does not release sand-like particles into drains.
- Transparent, white, grey and black options suit tile, acrylic, PVC and bathtub finishes.
- Custom strip width and roll length help reduce cutting waste during installation.
- Dot, oval and strip shapes can improve water movement around drains and curved trays.
- Adhesive level can be adjusted after testing tile, acrylic tray, PVC floor or coated bathtub surfaces.
- Typical 24-72 hour wet checks help review edge lifting, peel change, adhesive overflow and residue risk.
- Card packs, sheet packs and roll packs can be checked with physical samples before mass production.
Which strip, dot or oval format is better for wet bathroom surfaces?
The best format depends on how people step on the surface and how water drains after use. Long strips work well on shower floors, hotel bathroom walkways and bathtub entry zones where a continuous grip path is needed. Round dots and oval pieces are better for curved bathtub bottoms, acrylic trays and areas near drain holes because water can pass between each piece instead of collecting along one long tape edge. For private label bathroom safety tape, the product can be supplied as rolls for later cutting, kiss-cut sheets for fast placement, or separated die-cut pieces with controlled spacing. Before production, samples should be checked for edge lifting, barefoot comfort, wet peel performance and die-cut tolerance, usually around +/-0.8mm depending on shape and material thickness.
Applications
- Shower room floors in hotels, apartments, gyms and care facilities
- Bathtub bottoms, acrylic shower trays and wet stepping zones
- Bathroom tile floors where transparent tape keeps the original surface visible
- Pool changing rooms, spa rooms and locker room barefoot areas
- Private label wet-area tape packs in roll, sheet or pre-cut format
- Pre-cut strip, dot and oval layouts for drainage-friendly installation
- PVC bathroom floors where wet holding, clean removal and residue risk must be tested first
How should adhesive level and packaging format be confirmed before production?
Adhesive level should be tested on the real bathroom surface before bulk production. Smooth ceramic tile, acrylic shower trays, textured PVC floors and coated bathtub surfaces may need different adhesive strength to balance wet holding power and clean removal. A 24-72 hour sample test after water exposure helps confirm whether the tape stays flat without adhesive overflow, edge curling or visible residue. Packaging should also match the way the product will be installed or displayed. Roll packs are practical for project installers, while card packs, sheet packs and pre-cut strip sets are better for bathroom safety grip products supplied under a customer label. Surface cleaning instructions, barcode position, size details, printed color and roll length tolerance should be checked together with the physical sample.
FAQ
Can this tape be used on wet shower floors?
Yes. It is designed for wet bathroom use, but the surface should be cleaned, dried and tested first. A 24-72 hour wet exposure check is recommended before larger application.
Is transparent anti slip bathroom tape available?
Yes. Transparent PEVA/PVC tape is available for tile, acrylic tray and bathtub areas where the original surface appearance should remain visible.
Can the tape be made into dots or oval pieces?
Yes. Strip, dot, oval and special die-cut shapes can be produced according to drawings, sheet layout or private label pack design.
Will the tape leave residue after removal?
Residue depends on surface type, adhesive level, dwell time and cleaning conditions. Sample testing should check wet peel, edge lift and residue before production.